Simplify maintenance with CHS Natural Gas and Propane Plans
Routine maintenance is the best way to keep your natural gas and propane equipment running at its best – and to spot common issues before they require costly repairs.
CHS Natural Gas and Propane Plans are a great way to simplify routine maintenance. Available at two pricing levels – Priority Plan (ideal for newer and well-maintained systems) and a more comprehensive Ultra Plan (better for older systems, or for more peace of mind) – these plans will take the worry and hassle out of keeping your natural gas equipment running at its best.
See below for more details on what each plan covers. And don’t forget: You can also get CHS Service Plan coverage for your gas-fired water heater – or coverage for additional home comfort equipment via our other home service plans!
Priority Plan
Your CHS Priority Plan coverage includes:
- A 15-point tune-up performed once during the service agreement term during regular working hours. Contact us to schedule yours.
- 15 percent off all repairs
- 15 percent off diagnostic fees
- No after-hours charge
Ultra Plan
Your CHS Ultra Plan coverage includes:
- A 15-point tune-up will be performed once during the service agreement term during regular working hours. Contact us to schedule yours.
- Priority Service
- No diagnostic fee
- No after-hours charge
- Repair coverage for more than 35 parts in your system
Loyalty Credits
Save even more with CHS Loyalty Credits
For each consecutive year you are enrolled in our Priority or Ultra Service Plan, you earn $50 in Loyalty Credits. You can accumulate up to $700 in credits and apply them to equipment purchased from us, including:
- Boiler (up to $350)
- Furnace (up to $350)
- Central AC system (up to $350)
- Heat pump (up to $350)
Priority Plan
Your CHS Priority Plan coverage includes:
- A 15-point tune-up performed once during the service agreement term during regular working hours. Contact us to schedule yours.
- 15 percent off all repairs
- 15 percent off diagnostic fees
- No after-hours charge
15-Point Tune-Up
- Test carbon monoxide levels
- Clean and adjust burners and inspect heat exchanger
- Check thermostat operation
- Lubricate all motors, bearings, fans and circulator pumps
- Clean pilot assembly
- Test and adjust operation of safety and operating controls
- Inspect flue pipe and gas valve
- Clean and check blower motor (and belt if applicable)
- Test and tighten all wiring and connections
- Turn exposed dampers to heating position if marked (no balancing)
- Flush condensate drain to protect against overflow
- Check temperature rise
- Check fan speeds
- Check gas pressure at gas valve
- Inform customer of equipment condition; recommend necessary repairs
Ultra Plan
Your CHS Ultra Plan coverage includes:
- A 15-point tune-up will be performed once during the service agreement term during regular working hours. Contact us to schedule yours.
- Priority Service
- No diagnostic fee
- No after-hours charge
- Repair coverage for more than 35 parts in your system
System Parts
- Blower belt
- Blower motor (1/3-3/4 hp; psc only)
- Blower motor pulley
- Circulator coupling (1 zone)
- Circulator motor
- Circulator relay
- Combination control
- Draft inducer motor
- Emergency switch
- Fan and limit control
- Flue pipe
- Gas valve
- Glow ignitors
- High limit control
- ICM control board
- In-line draft diverters
- Low limit control
- Low voltage transformer
- Pilot assembly
- Pressure switch
- Pressuretrol
- Primary control
- Reverse aquastat
- Rollout switch
- Single aquastat
- Spill switch
- Thermocouples
- Thermostat (nonprogrammable)
- Triple aquastat
Gas Burner Parts
- Burner orifice
- Gas valve orifice
- Pilot tube
- Sensor
- Sensor ignition module
Other parts
- Altitude and temperature gauge
- Thermostat sub base
Services
- Carbon monoxide testing
15-Point Tune-Up
- Test carbon monoxide levels
- Clean and adjust burners and inspect heat exchanger
- Check thermostat operation
- Lubricate all motors, bearings, fans and circulator pumps
- Clean pilot assembly
- Test and adjust operation of safety and operating controls
- Inspect flue pipe and gas valve
- Clean and check blower motor (and belt if applicable)
- Test and tighten all wiring and connections
- Turn exposed dampers to heating position if marked (no balancing)
- Flush condensate drain to protect against overflow
- Check temperature rise
- Check fan speeds
- Check gas pressure at gas valve
- Inform customer of equipment condition; recommend necessary repairs
Customer Reviews
Special Offers
Become a Customer
Refer a Friend